Renray Corus Electric Four Section Profiling Bed with Hospital Mattress SelfiMed UK

Käytetty

Merkki

Harvest Healthcare Leeds, Yhdistynyt kuningaskunta

Varastossa Iso-Britanniassa, lähetetään Leedsistä

Kaikki tuotteet / Hospital bed

Renray Corus Electric Four Section Profiling Bed with Hospital Mattress

Name: Renray Corus Electric Four Section Profiling Bed with Hospital Mattress
Brand: Harvest Healthcare
SKU: REN4172V
Price: 499.99 GBP
Availability: InStock
Rating: 4.9 (7 reviews)

Harvest HealthcareSKU REN4172V

Hinta

£499⁹⁹

Price shown excludes VAT.

VAT relief available on this product

Eligible customers can claim VAT relief on this product at checkout.

Claim VAT relief I confirm I am chronically sick or disabled and these goods are for my personal or domestic use. I claim relief from VAT.

Määrä

Yksikköhinta£499.99

Yhteensä£499.99

Free UK mainland delivery on orders over £1,000

Haluatko mieluummin tarjouksen?

Pyydä tarjous

Usein ostetaan yhdessä

Lisää koko sarja kerralla.

Direct Healthcare Dyna-Form Mercury Advance – dynaaminen ilmapatja pumpulla £199.99 ~~£241.99~~ Sisällytä

Huntleigh Nimbus 3 – vaihtuvapaineinen painehaavapatja pumpulla, käytetty £149.99 Sisällytä

Squirrel Medical 8535 ilmapatjajärjestelmä – uusi £299.99 ~~£499.99~~ Sisällytä

Potilaan vuodepöytä, polymeeri £199.99 Sisällytä

Sarja yhteensä £0.00

Tärkeimmät ominaisuudet

Merkki: Harvest Healthcare
Kategoria: Hospital bed
SKU: REN4172V

Renray Corus Electric Four Section Profiling Bed with Hospital Mattress, Pre-owned

The Corus is Renray Healthcare's electric profiling bed, built in Cheshire for community and care home use. It profiles in four sections, raises and lowers on powered height adjustment, tilts both ways, and carries a safe working load of 180 kg with a maximum patient weight of 150 kg. The handset locks with a key.

Renray build the Corus in two heights, and which one this is matters more than anything else on the page. The Corus 1000 drops to a platform height of 195 mm, which is a genuine low bed: paired with a falls mattress it is specified to reduce injury when a resident rolls out, because there is very little height to fall through. The Corus 2000 runs from 300 mm and is a standard height bed. Both rise to a working height for care, so the low bed does not cost the carer anything in return.

Four section profiling means the backrest raises to around 70 degrees, the knee break lifts to 17 degrees, and vascular and Fowler leg positions are available from the handset, with the calf section adjusted by hand. Tilt runs to 10.5 degrees either way, foot down as standard and head down as an option, which is the function that matters for a resident who slides down the bed and has to be repositioned.

Two details mark this out as a care home bed rather than a hospital one. The handset carries a lock-out key, so a resident who would otherwise alter the bed through the night cannot, and the carer can still use it. And in a power cut, two 9 V alkaline cells drive enough emergency function to flatten the deck and lower the bed, which is what a night carer needs when the lights go out with someone sitting up. The frame is powder coated with rounded corners, the head and foot panels carry wood effect inserts that soften the look of the bed in a bedroom, and it rolls on four 100 mm braked castors over a slatted platform. Supplied pre-owned with its handset, both panels and a hospital mattress, which is selected at the point of order as either foam or an alternating air system.

References

Brand	Renray Healthcare
Range	Corus
Model	Read from the bed label and confirmed before dispatch
Low height model in the range	COR1000, platform 195 to 600 mm
Standard height model in the range	COR2000, platform 300 to 705 mm
Wide model in the range	COR2400, 4 ft wide
Safe working load	180 kg, including mattress and fitted accessories
Maximum patient weight	150 kg
Profiling	Four section
Mattress	Hospital mattress supplied, foam or alternating air, selected at order
Condition	Pre-owned

Features

Four section profiling with powered height adjustment.
Backrest raising to around 70 degrees and knee break to 17 degrees.
Vascular and Fowler leg positions from the handset, with the calf section adjusted by hand.
Tilt to 10.5 degrees, foot down as standard and head down as an option.
Handset with a lock-out key, so a resident cannot alter the bed while the carer still can.
Emergency lowering on two 9 V alkaline cells, enough to flatten the deck and lower the bed in a power cut.
Safe working load of 180 kg including the mattress and anything fitted to the bed.
Integral 115 mm bed extension with a mattress retainer, for a taller resident.
Four 100 mm castors, each with a foot operated brake.
Powder coated frame with rounded corners, wiping down cleanly.
Removable head and foot panels with wood effect inserts, which soften the look of the bed in a bedroom.
Slatted platform, lighter than a solid deck and allowing air through the mattress.
Hospital mattress included, chosen at order as foam for general nursing or an alternating air system for pressure redistribution.
Mattress matched to the bed, so the depth is known before side rails are specified.
Built in the United Kingdom by Renray Healthcare.
Specified to IEC 60601-2-52, the standard for medical beds.

Points to note before ordering

Low height or standard height is the question to settle first. The Corus 1000 drops to 195 mm at the platform and is a falls prevention bed; the Corus 2000 starts at 300 mm and is a standard height bed. They look similar and the model number is what tells them apart. Elarix Medical reads the model from the bed and states it in writing before dispatch, with the measured height range.
The mattress choice decides which side rail fits. Renray make two rail heights for this bed: the standard rail for mattresses up to about 150 mm deep, and the extra height rail for mattresses up to about 250 mm. An alternating air system sits deeper than foam, so it generally calls for the extra height rail. Fitting a deeper mattress under a standard rail lowers the effective rail height and takes the combination outside the dimensional limits in BS EN 60601-2-52 and MHRA bed rails guidance. Gaps are never packed out with bedding, which compresses. Rails are not included and are quoted against the mattress chosen.
Safe working load includes everything on the bed. The 180 kg figure covers the mattress and every fitted accessory, so the maximum patient weight is 150 kg. A lifting pole, a grab handle and a deep mattress all come out of that allowance.
Choose the mattress at the point of order. A hospital mattress is included and is supplied either as foam or as an alternating air system with its pump. Foam suits general nursing. An alternating system is for a resident at raised risk of pressure damage and sits deeper on the platform. Where this is the low height Corus 1000 used as a falls bed, a falls mattress is the surface that completes the arrangement and is quoted separately.
Pre-owned condition and commissioning. Marks to the frame and panels consistent with service use. Decontamination to local policy, electrical safety testing and a function check of every actuator, the castor brakes, the handset lock and the emergency lowering are carried out before use. The emergency cells are changed at least yearly and are confirmed before dispatch. Elarix Medical photographs the actual bed on request.

Tekniset erittelyt

Brand: Renray Healthcare
Range: Corus
Model: Read from the bed label before dispatch
Condition: Pre-owned
Device type: Electric four section profiling bed
Safe working load: 180 kg, including mattress and fitted accessories
Maximum patient weight: 150 kg
Patient height range specified by Renray: 146 to 185 cm
Platform height, COR1000: 195 to 600 mm
Platform height, COR2000: 300 to 705 mm
Height range of this bed: Measured and confirmed before dispatch
Overall length: 2163 mm, 2278 mm extended
Bed extension: 115 mm, integral, with mattress retainer
Overall width without rails: 937 mm
Overall width with three quarter rails: 1012 mm
Mattress platform length: 1965 mm, 2080 mm extended
Mattress platform width: Confirmed from the bed before dispatch
Platform type: Slatted
Mattress: Hospital mattress supplied, matched to the bed
Mattress options: Foam, or alternating air system with pump
Mattress selection: Made at the point of order
Side rail height needed: Determined by the mattress depth chosen
Head and foot panels: Fitted, wood effect inserts in moulded surrounds
Side rails fitted: None
Profiling sections: Four
Backrest angle: 0 to around 70 degrees
Knee elevation: 0 to 17 degrees
Calf section: Manually adjusted
Leg positions: Vascular and Fowler
Tilt: 10.5 degrees, foot down standard, head down optional
Handset: Function buttons with a lock-out key
Emergency lowering: Two 9 V 6LR61 alkaline cells, changed at least yearly
Castors: Four at 100 mm, each with a foot operated brake
Mains supply: 230 to 240 V alternating current, 50 or 60 Hz
System voltage: 24 to 29 V direct current
Maximum current: 2.0 A, 52 W
Side rails, standard height: CORSSR, for mattresses up to about 150 mm, not supplied
Side rails, extra height: CORESR, for mattresses up to about 250 mm, not supplied
Lifting pole: ELP, safe working load 75 kg, not supplied
Grab handle: COREGH, not supplied
Finish: Powder coated, rounded corners, removable head and foot panels
Standard for medical beds: IEC 60601-2-52
Rail height required above uncompressed mattress: At least 220 mm along at least half the platform length
Cleaning: Surface decontamination to local policy, no immersion of handset or actuators
Commissioning: Electrical safety test and function check of actuators, brakes, handset lock and emergency lowering