The Park House Endeavour 3000 Electric Hospital Bed is a profiling bed designed for clinical and home-care use. It offers electrically powered height, backrest and leg-rest adjustment, allowing carers and clinicians to position a patient without manual effort. This article explains what the bed is, how it works, what to check before ordering and what is not included as standard.
The Endeavour 3000 is a multi-section profiling bed. Electric actuators drive the backrest, leg rest and overall bed height independently. The carer operates each function via a pendant handset. A second handset is usually provided for the patient, though this varies by configuration.
The bed is intended for ward, community hospital and home-care environments where manual handling reduction is a clinical priority. Electrically powered height adjustment allows the carer to work at a safe height and then lower the bed close to the floor for the patient.
The Endeavour 3000 is used in NHS trusts, independent hospitals, residential care homes and private home-care settings. It is also purchased by community equipment services for short-term loan. Pre-owned units are common in the secondary market because the steel frame and actuator system are built for long service life.
 |
Park House Endeavour 3000 Electric Hospital Bed with Hospital Mattress £599.99 Buy nowView product |
The Endeavour 3000 typically offers four-section profiling: backrest rise, knee break, leg elevation and Trendelenburg or reverse-Trendelenburg tilt, depending on the specific variant. Not every variant includes all four functions. Confirm the configuration of the unit offered before ordering, particularly for Trendelenburg, which is not always present on community-grade variants.
Height range varies by variant. Most Endeavour 3000 units adjust from approximately 37 cm to 80 cm at the mattress platform. Photographs and the seller's specification sheet should be checked because platform height affects bed rail selection and fall-risk assessment.
The bed runs from a standard 230 V UK mains supply. The control box is integrated into the frame. Each actuator is individually fused. The pendant handset connects via a multi-pin socket, and a spare or replacement handset is available separately from Park House and from approved parts suppliers.
Battery backup is not a standard feature on the Endeavour 3000. If a power cut occurs, the bed remains in its current position. Organisations planning use in areas with unreliable mains supply should factor this into their risk assessment.
The pendant handset on most Endeavour 3000 variants includes a single-press function to move the backrest to flat in one action. This is relevant for cardiopulmonary resuscitation positioning. Confirm that this function is present and working on the specific unit before clinical deployment.
A standard Endeavour 3000 supply typically includes the bed frame, the mattress platform sections and the carer pendant. Side rails, patient pendant, mattress, bed bumpers and IV pole brackets are configuration-dependent. On pre-owned units, some of these items may be absent, damaged or non-matching.
Photographs form part of the description on any pre-owned listing. Review them carefully. If a component is visible in the photograph but not listed in the included items table, ask before ordering.
Not all hospital mattresses fit the Endeavour 3000 platform without modification to the platform length or width. Standard UK hospital mattress dimensions apply, but the profiling deck must be checked for section lengths before ordering a specialist mattress. Bed rails must be the approved type for this frame. Fitting non-approved rails creates an entrapment hazard. The rail manufacturer's documentation should accompany any rail set.
The Provision and Use of Work Equipment Regulations 1998 (PUWER) apply when the bed is used in a workplace, including a care home or NHS facility. The operating organisation is responsible for periodic inspection, portable appliance testing and maintenance records. These obligations are not discharged by an in-house dispatch check.
A used bed that has been cleaned and function-tested before dispatch is not the same as a bed that has undergone a full engineer service. If the listing does not state that the unit has been serviced, assume it has not. Plan maintenance accordingly.
Bed rail entrapment is a recognised clinical risk. The Medicines and Healthcare products Regulatory Agency (MHRA) guidance on bed rail safety applies to the Endeavour 3000 when rails are fitted. The gap between the mattress, the rail and the frame must be assessed for each individual patient. This assessment is the responsibility of the clinical team, not the supplier.
Never fit rails from a different bed model without written confirmation from the rail manufacturer that they are compatible with the Endeavour 3000 frame and the mattress in use.
A pre-owned Endeavour 3000 must be decontaminated before patient use. The operating organisation must follow its own infection prevention and control protocol. A dispatch clean is a transit clean, not a clinical decontamination. The responsible clinician or infection control lead should sign off the bed as fit for patient contact before it is placed in a ward or room.
The Endeavour 3000 frame is heavy. Delivery to upper floors without lift access may not be possible with a standard courier. Measure all doorways, corridors and the lift car before confirming delivery. The assembled bed is wider than a standard domestic doorway. Some organisations take delivery of the frame in sections and reassemble on site.
Park House Medical is the manufacturer. Spare actuators, handsets, control boxes and rail sets are available through approved distributors. When ordering a pre-owned unit, note the serial number and confirm with the supplier which spare parts remain available for that production variant.
Pre-owned Endeavour 3000 beds vary in condition. A unit from a ward closure may have high hours of use and cosmetic wear but a functioning actuator system. A unit from a short-term loan pool may have fewer hours but incomplete accessories. Ask for the usage history, inspection records and any known faults before committing to purchase.
The Park House Endeavour 3000 Electric Hospital Bed is a well-established profiling bed used across NHS and independent care settings. It offers electrically powered height and section adjustment, a durable steel frame and a proven actuator system. Key points to confirm before ordering are the exact profiling configuration, which accessories are included, the condition and history of the unit, and whether the accessories such as rails and mattress are compatible. PUWER, MHRA bed rail guidance and the operating organisation's decontamination protocol all apply before the bed enters service. A pre-owned unit cleaned and tested before dispatch is not a fully serviced unit. Plan maintenance, electrical safety testing and decontamination as separate steps after delivery.
|
Ready to move forward with the Park House Endeavour 3000 Electric Hospital Bed with Hospital Mattress? Shop the Park House Endeavour 3000 Electric Hospital Bed with Hospital Mattress |
Einen Kommentar hinterlassen